![]() One of the new selections will be a category called “Wirecast Cam”. Once again select the camera icon in the upper right which will open a series of options as seen below, although your exact options will vary. Now, once again, below the preview windows hover over the + icon next to a “blank shot”. When you have connected successfully, click the red X in the upper left. If so, you will need to click ALLOW ACCESS. Note that, depending on your settings, you might get a prompt to allow access through your firewall, as seen to the right. This will replace the green area with a live preview of your Wirecast Cam. This is important, if you don’t click it the encoder will not be able to connect to the App.Īfter you have clicked the record in the App, click the CONNECT button on the source settings menu. Inside the App click the giant red record button as well, turning the circle into a red square. The first order of business is to enter in the IP Address that you jotted down from the App Settings screen inside the Wirecast Cam App. The Source Settings pop up will then refresh with a screen that looks like below: One of these options is the ability to “Add Wirecast Cam”. This will present a series of options that include the ability to add a “Local Desktop Presenter”, a “Web Stream” and more. Once clicked, a pop up like below will appear.Ĭlick the “+▼” button in the lower right. Unless you happen to see Wirecast Cam as an option, you will need to click “Show Sources Settings…” as seen in the picture below (note: your drop-down choices will vary but Show Sources Settings will always be the final option). This will present a drop-down series of options to select a video source. The camera icon in the upper right needs to be clicked, as seen in the image. ![]() Hover over the + icon, which will display four options. Below the preview windows will be a series of “blank shot” listings. Now that you have set up the Wirecast Cam app, the next step is to select it inside the encoder.įirst, launch your version of Wirecast on your desktop or laptop. Selecting the Wirecast Cam Inside the Encoder This will be later entered into the encoder to sync it with the app. The audio button is, curiously, another way to mute the stream separate of the on-panel option to mute.įinally, the IP address is important and something you will need to jot down. When using this app, though, that consideration is reduced since you are almost streaming twice. Generally, you don’t want the bitrate to exceed half of your internet upload speed. This can cause a inflated need for a higher bitrate. However, the Wirecast Cam app is actively sending this video signal to the encoder. The Wirecast encoder and the Wirecast Cam app would both need to be synced to achieve this. Please note that simply because you have a high bitrate here does not mean you will be live streaming to viewers at that rate. The resolution, keyframe interval, and bitrate are related to the quality of the stream. Once clicked, you will see a few options here. This is an important aspect of the app to look at. The button doesn’t change to signify which camera is being used, but it should be obvious from the preview window. ![]() For example, you can change from the front to the rear camera. The final button switches the camera being used. So it needs to be streaming from both the app and encoder at the same time for the content to be actually live streaming. Please note that even if you are “streaming” here, the encoder itself houses the ultimate control. Once you click this the red circle changes to a red square. The red circle, naturally, is the stream button. There are a lot of features here, and also important information criteria as well. The gear icon controls the settings for the Wirecast Cam App. When clicked, a strikethrough will appear on the microphone and the audio will be muted. It is pretty straight forward in that it’s either active or muted. The first controls the audio for the stream. Let’s walk through the four main buttons available here. You’ll see a screen that looks like this: Getting Startedįirst, open your Wirecast Cam app. In particular version 6.0.1 or higher of the encoder. You can install the app on your device for free, but you’ll need the Wirecast encoder on a laptop to actually stream with the app. It can be used with either an iPhone or iPad and will utilize the device’s built-in camera as a source. The app is a free download and is available on the iOS app store. To note, the app is sadly not available on Android devices at this time. To begin, there are a few things that are needed Selecting the Wirecast Cam Inside the Encoder.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |